DTA ECU S60
Stunning performance combined with a truly impressive and expanding range of features
Designed to meet the demands of the latest generation of very high revving, four coil, sequentially injected engines, the S60 PRO is our latest ECU.
Aimed primarily at the advanced four cylinder market, the S60 PRO also caters for wasted spark non-sequentially injected engines of up to eight cylinders.
20,000 rpm capability Flexible and easily adapted to different OEM and custom crank and cam sensor arrangements. Genuine four and two stroke support. Twin spark engines. Twin injector engines. Sequential or grouped injection. Individual coils, wasted spark or distributor. Unequal coil firing capability. Unequal injection angle capability. Delayed sequential injection. User controlled fan activation. Sensors can be calibrated individually with a lot of preset options supplied. Flexible Tacho Output Soft and hard rev limits
Main Fuel and Ignition Functions
Two main fuel, spark and turbo maps selected by a dashboard switch. Comprehensive start up fuelling options both time and temperature dependant. Air, coolant and manifold pressure compensation maps. Throttle transient increase compensation. Throttle transient reduction compensation. RPM and load breakpoints can be calibrated by the user. Throttle or MAP as load. All maps with one or two dimensional with interpolation as required.
Lambda control functions
Extensive lambda parameters table to ensure stable closed loop operation and emissions requirements can be met where needed. Full three dimensional lambda target map. Auto-tuning function. T
urbo Control Functions
Open or closed loop turbo pressure control via PWM valve. Modify target turbo pressure by gear selected. Modify target turbo pressure by vehicle speed. Two control maps selected by switch on dashboard. Active base PWM map for easy calibration.
Idle Control Functions
Open or closed loop idle speed control via PWM valve. Closed loop idle target speed temperature dependant. Active base PWM map for easy calibration. Fuel enrichment table calibrated versus PWM percentage.
ALS Control Functions
Full ALS ignition and fuel maps. ALS valve control together with map switching controlled by dash board switch.
Cam Control Functions
Open or closed loop cam advance control via PWM valve. Static offset table to zero out electrical movement effects. Active Cam Target Advance map, load and speed dependant. Active base PWM map for easy calibration. VTEC Control
When not being used to control the camshaft, cam base PWM map can be used instead for water injection, giving complete load and speed dependence.
Three uncommitted input tables which use 0 - 5 volt inputs or any input the S60 knows already, linked to fuel and advance modifiers and a PWM output.
Fully flexible first gear launch capability. Extensively tunable to individual vehicles.
Full Throttle Gear Shift Cut
Shift cut capability with 1ms resolution, variable for each gear with full switch de-bounce capability.
Voltage Compensation Tables
User configurable voltage compensation tables for injector dead time and coil on time (dwell time).
Diagnostics and Test Features
Full sensor diagnostics and fault recording. Extensive engine run time recording at different load and speed conditions. Ability to exercise injectors and coils without engine running for fault finding.
The ECU firmware is flash upgradeable via the serial port with a special cable and software. Current firmware and software published on http://www.dtafast.co.uk.
CAN PC Communications
The ECU can communicate with the PC via our USB -> CAN converter. This solves the problem of unreliable USB -> RS232 converters.
Up to thirty six separate items can be logged. Three user selectable logging frequencies. Up to nine hours logging capability. Graphing can be done on-line to the ECU.
Water Resistant Enclosure Sealed Latching Connectors Size 134 x 134 x 46 mm Weight 679 gm All outputs protected against over temperature and over current Inputs protected against severe wiring mistakes and accidents Reverse battery protection Alternator load dump protection
Inputs and Outputs
Crank Shaft (Magnetic and Hall Effect) 1 x Cam Shaft (Magnetic and Hall Effect) Throttle Position Coolant Temperature Air Temperature Manifold / Barometric Pressure Lambda Oil Pressure Fuel Pressur Oil Temperature Battery Volts 3 x User Defined Analogue (Shared Use) Launch Switch Shift Cut 1 x Wheel Speed ALS / Second Map Switch
4 x Coil Drivers 4 x Injector Drivers Tacho Fuel Pump Relay Fan Turbo Pressure Valve Turbo ALS Valve Cam Control Valve VTEC Valve Idle Valve Shift Light 6 x User Programmable Aux (Shared Use)
|1st Class Tracked & Signed upto 1kg||£7.32|
|1st Class Tracked & Signed upto 61cm||£9.90|